Same-day Washing Machine Repair Service

Piles of clothes or dishes make you crazy? No possibility to wait for tomorrow because you need absolutely clean clothes or dishes today? No worries, if you have applied to our repair service company. We will visit your place the same-day. Moreover, you don’t need to wait for required parts to be replaced because our vans are always equipped with all necessary spare parts.

  •  Factory Certified

    Factory Certified

    Licensed technicians with over 15 years of experience

  • TSSA Gas Contractor

    TSSA Gas Contractor

    Fully certified in gas appliances service, repair & installation

  • Complete Warranty

    Complete Warranty

    Each repair is covered by service and parts warranty

Common Washing Machine Issues

It is not obvious, but we listed the most common ones:

  • Washing machine won’t turn on/off
  • Washer makes some strange sounds or vibrations
  • It is not draining
  • Washer is not dispensing detergent
  • The clothes have the bad smell
  • Washing machine is not spinning
  • Washer door doesn’t open or close
  • Washing machine is not filling with water

Washer Repair Company You Can Trust

Years of experience made us the leading repair service company in Toronto. We are proud to be helpful to thousands of our happy clients. Satisfaction and references of our clients is the proof that we are doing our job at the high professional level.

Appliance technician

FAQ for any washer type

The first thing you have to check is the power supply. Make sure the rosette is functioning, and all connections are adjusted properly. The next thing to check is the lid switch.  It has to be positioned correctly and be shut.

Usually the clogged drain hose turns out to be the source of the problem. Detach the hose and thoroughly inspect it for kinks and any clog blockages in it. Remove any clog or debris.

It is most likely something has been stuck in the washer drum. To clarify whether there are any items you are to remove drum paddles. We also recommend checking the drain filter to assure yourself it is clean. Otherwise, you have to clean it.

One of the easiest solutions of this problem is not to overload your washer. Overloading makes the washer unbalanced, and as a result, it is not agitating properly.  

The drain hose has to be inspected. Make sure all connections on the hose are secure, and the hose itself is not damaged. Afterwards verify whether there aren’t any clogs to be removed. Replace a new hose if it cannot be cleaned or repaired.

Your washer is supposedly standing on the uneven floor. You can use the piece of plywood so the washer would be positioned correctly.

What can you undertake if your LG washer stops mid-cycle? There might be the power surge. Unplug your washing machine and after 1-minute plug it back in. Open and shut the washer door several times within few seconds. Test your washer, having set the shortest cycle without any clothes inside.

Although you can own the good Whirlpool washer, you are not insured against bad washer smells. We recommend cleaning your washer every month. Inspect your appliance for mold or mildew which are considered to be the sources of the bed smell. To prevent mold, run a washing cycle with no detergent having loaded 2-3 small and clean towels. Don’t run your washing machine empty. Pour the vinegar to the tub and set the highest temperature.

If your Maytag washing machine doesn’t finish cycling, you should check the timer. Detach the control panel and inspect the timer connections. Use the multi-meter to check its continuity. In case no continuity is shown up, you are to replace it.

If you are the owner of GE washer, and it reports the fault code, please don’t ignore this sign. Thus, you will avoid many serious breakages. Fault codes are not universal, that’s why you should apply to the GE washer repair manual where you can probably find the solution of the issue. If you fail to fix it on your own, the knowledgeable and skilled specialists of GTA Appliance Repair will quickly identify the problem and fix it.

What to do if your washer is not filling with water. Actually this issue can happen to all washing machines, and Kenmore is not the exception. Just make sure you have closed the washer door properly. Verify whether the water supply is functioning. Afterwards inspect the inlet hoses – they should be free of clogs and kicks.